Skip to main content

Ultramarine 10-man Tactical Squad (2)



The second squad is now complete.  Inevitably it has come out better than the first one due to reviewing and learning from the first group I put together.  This build uses new kit as well as a few components from the Sternguard box.  Again I have gone for Combi-Flamer and Flamer, however I have chosen to build a Missile launcher into this Squad rather than the more costly Lascannon.  In time this unit will get a Rhino as well, with the first Rhino now 99% complete and needing a write up for the blog.



A change I made on this unit was to go a bit heavier with the VMA Light Sea Blue to get a better contrast after the oil wash and satin varnish was applied (these generally dull your highlights).

The transfers on this unit came out really well and I think I have refined how I will approach transfers from now on.  The GW hard coat gloss brushed on seems to give better adhesion than any airbrushed gloss varnish when it comes to sticking in transfers.  The red and blue containers of Micro Set and Micro Sol also seem to work better than the Humbrol Decal Fix.  The process for applying my transfers consists of the following:



1.  Complete the model to the stage of needing an oil wash next.
2.  Brush varnish GW hard coat gloss onto the areas that require a transfer.
3.  Cut the transfers out but also cut small lines into the edges of the transfer to allow the flat decal to form around 3D curves.
4.  Soak the transfer in Micro Set and allow softening of the decal to take place.
5.  Apply transfer with brush and scalpel carefully, and remove excess Mirco Set with paper towel pressing down to make sure the transfer is on.
6.  Allow to dry thoroughly.
7.  Apply Micro Sol a few hours later gently brushing some over the transfer.
8.  Allow to dry thoroughly again and repeat stage 7 at least one more time.  You can do this as often as you like until the transfer fits the shape (typically the rounded shoulder pad).
9.  Satin varnish your work and move onto your oil wash so as to include the transfer in any weathering that you wish to apply.  The transfer should look like it is completely painted on.

The photos below show some of the key stages in production.












Comments

  1. Where did you find corks that fat n flat? Looks good by the way.

    ReplyDelete
  2. The cork cups are from Forgeplant.com and are the same ones used by Buypainted! I think. Really useful for any and all infantry projects.

    ReplyDelete

Post a Comment

Popular posts from this blog

House Cadmus Imperial Knights

This post has been sat in my archive for far too long. I am not going to pretend it is new work - it has been up on my Instagram for some time but I thought I would show you some WIP photos and talk through some tips on making what is a very large project manageable. Hopefully of use to someone out there! Three Kinghts is a decent amount of work - but to be fair, you pretty much have an army once you are done.  To keep me motivated and to make the project achievable I broke it down into stages: 1. The Metal Skeletons 2. Panel Work 3. Bases 4. Weaponry. This approach will save you time and will help you get 3 Knights above table top quality quickly and efficiently. It won't feel like it as you go - but trust me when you reflect, you will have saved yourself some serious time.  There is also a uniformity you can't replicate from doing 1 then adding 2 later on... Take the pain and work in multiples....read on... 1. The Metal Skeletons: Army Painter Silver Rattle Ca

Forge World Scorpion Type II – Saim-Hann

Forge World Scorpion Type II – Saim-Hann With my first project under my belt, I dug out a Forge World kit that had been left under the bed for a good number of years.  I could not ge the smooth finish I wanted so parked the model to one side, but never came back to it.  All the practicing of pre-shading, zen highlighting and shading using the Falcon kits drove me to dig it out and get it done.  This will be more step by step but do ask questions below if you want something made clearer.  Again, Buypainted! gave a vast amount of guidance and inspiration - credit where credit is due! 1.                The main hull was constructed, wing-lets, tail section etc.  The turret was also built however don’t do what I did initially and leave the pulsars sperate.  The crew and smaller weapons were mounted on old sprues to assist in painting.  The whole lot was primed us Vallejo Polyurethane Grey Primer – great stuff, and key to get the different sh

Ultramarines Super Heavy Falchion Tank

Finally finished the Falchion and another model in line with the core theme of the blog.  I picked this up back in March at the Forge World open day, with a view to have it finished before wider release... anyway...  it's done now.  The techniques involved are covered in the Glaive tutorial.  This time around I have tried to apply some of the pointers and tips passed on from Matt Murphy-Kane and Mark Bedford from not only Warhmmer Fest, but the FW open day to.